| |
Preparation of
Manuscript for SimPro08
Shunichi
Hashimoto1 and Saugo Miyake2
1CBMM Asia Co. Ltd., Tokyo, 107-0052, Japan
2Kobelco Research Institute, Ikeda, Onoe-Cho, Kakogawa, Hyogo, 675-0023,
Japan
E-mail : Shasimoto@cbmmasia.co.jp
|
|
|
ABSTRACT
To ensure that papers will
be reproduced clearly and in proper size, authors should observe
following instructions. The manuscript must be typed in two columns, to
a page on white A4 size papers. The number of pages is up to 10 for both
contributed and invited papers. Please give an abstract at the top of
the manuscript in single column. The abstract should clearly state the
outline of paper. This document is itself an example of abstract,
layout. The deadline of manuscript submission is June 30, 2008. The
manuscripts should be submitted either by e-mail or posted directly in
our web-site (www.simpro-ranchi.com).
Keywords : steel, instruction, Kitakyushu, conference
(Keywords are to be separated by comma.)
****
INTRODUCTION
Authors of accepted abstracts are requested to submit the final
manuscript in English. The authors will be duly notified by e-mail as to
acceptance of their papers by February 15, 2008. At least one author of
the paper should complete the registration before end of October 2008,
for the paper to be published in the Conference Proceedings. The general
requirements of formatting are as follows :
File
format : MS Word 2003 document
Paper size : A4
Margin : Left - 2.5 cm, Right - 2.5 cm, Top - 2.5 cm & Bottom - 2.5 cm
Total no. of pages : Upto 10 pages (recommended) including all tables,
figures etc.
Font type : Times New Roman
Font size : Title : 16 points (bold), Authors name and affiliation : 11
points, Main text : 10 point, Heading & Sub-heading: 10 point (bold)
Line spacing : 1.5
Columns : Double column format
Note : Please do not use local font such as Chinese, Russian, Japanese
etc. in the text or figures as readers who do not have them on the
computer will be unable to read the file.
TEXT
Clear differentiation should be made between the headings of sections,
subsections. etc. All Sectional Headings should be in capital letters
and on a separate line. Sub-headings should be in title case and again
on a separate line. Authors are requested to submit their papers using
SI units.
TABLES
Tables should be kept as simple as possible. Each table should have a
title in title case. Column headings should be as brief as possible and
the number of columns should be kept to a minimum.
****
ILLUSTRATIONS
Drawings and
Photographs
Figures should be appropriately sized so that they fit within the
column. Only special cases, it may be formatted in single column mode.
Figures should be placed within the text as close to their mention as
possible. All figures and illustrations should be in black and white.
Authors should avoid colour images or photographs, as they will not be
reproduced well in prints. On graphs, show only the coordinate axes, or
at most the major grid lines, to preclude a dense hard-to-read effect.
All lettering should be large enough to remain legible after
photographic reproduction, i.e., at least 2.5 mm in height.
Digital Images
Digital images such as line art and photographs can be used if the
output resolution is at least 300 dpi.
****
ACKNOWLEDGEMENT
Acknowledgements should appear in a section immediately preceding the
references.
****
REFERENCES
The references should be set out in a list, numbered according to their
appearance in the text. When referring to them in the text, type the
corresponding reference number in square brackets at the end of its
sentence. [1]. All references given should be complete and formatted as
given below :
****
Example
Journal :
H.
Kim and R.J. Fruehan, ISIJ International, Vol. 38, No. 5, 1998, p. 430.
Books : A.K.
Tripathy and H.S. Ray, Quantitative Approaches in Process Metallurgy,
1st Ed., Allied publisher, London, 1995, p. 25.
Conf.Proc. : S.S.
Ray and T.K. Ghosh, Proc. Int. Conf. on Continuous Casting of Steel, Ed.
By denys, The Metals Society of IRSID, Biarritz, 1976, p. 248.
|
